P0328: Knock sensor 1 circuit high input (bank 1 or single sensor)
The ECU sees a knock sensor signal that is too high. Often a wire touching a live feed, the connector, the sensor itself or excessive engine noise.
| Code | P0328 |
|---|---|
| System | Engine and transmission |
| Group | P03xx, Ignition and misfires |
| Type | Generic: it means the same on every make |
| Can you keep driving? | With care |
What P0328 means
The knock sensor is bolted to the engine block and works like a microphone: it picks up the vibration of knock (detonation, fuel burning at the wrong moment and hammering the pistons). When it hears it, the ECU retards the ignition to protect the engine. High input means the ECU is reading a voltage above what is possible, usually from an electrical fault, although loud mechanical noise can also play a part. It is sensor 1, on bank 1 or the only one.
Most common causes
- Moisture or corrosion in the connector
- Bare sensor wire touching another live wire
- Interference from nearby ignition leads
- Loud mechanical engine noise
- Failed knock sensor
Symptoms
- Less power, especially under hard acceleration
- Slightly higher fuel consumption
- Engine warning light on
- Sometimes no noticeable symptoms
Can you drive with P0328?
With care You can drive, as the ECU usually retards the ignition as a precaution, but the engine is less protected if real knock occurs. Avoid working it hard and get it checked soon.
Open the bonnetthe in-depth explanation
How to check it
With the engine idling, listen for knocking or metallic noises that were not there before: if there are, mention it to the garage, as the sensor may be picking up a real noise rather than being faulty itself.
How to read and clear P0328 with Final OBD
Plug an OBD2 scanner in under the steering wheel, switch the ignition on and open Final OBD. Under Faults you’ll see P0328 with its description and whether it’s confirmed, pending or permanent.
If the engine stores it over standard OBD, with FREE you read this code with its explanation for nothing and clear it. With PRO you also read the faults of every control unit and clear them in all of them.
Clearing the code only turns the light off: if the cause is still there, it comes back. Clear it once it’s fixed, and not right before an inspection. It’s all in how to read and clear fault codes and in inspections and OBD.
Similar codes
- P0324 There is a fault in the engine knock control system
- P0325 Knock sensor 1 circuit fault (bank 1 or single sensor)
- P0326 Knock sensor 1 signal out of range (bank 1 or single sensor)
- P0327 Knock sensor 1 circuit low input (bank 1 or single sensor)
- P0329 The circuit signal from knock sensor 1 on bank 1 is intermittent
- P032A The knock sensor 3 (bank 2) has an electrical fault
- P032B The knock sensor 3 (bank 2) gives readings outside the normal range
- P032C The knock sensor 3 (bank 2) gives a lower signal than normal
- P0300 Random or multiple cylinder misfire
- P0301 Misfire detected in cylinder 1
- P0302 Misfire detected in cylinder 2
- P0303 Misfire detected in cylinder 3
To understand it properly
We explain how that system works, with drawings and no waffle, in our mechanics guide: Knock and pre-ignition.
What does code P0328 mean?
The knock sensor is bolted to the engine block and works like a microphone: it picks up the vibration of knock (detonation, fuel burning at the wrong moment and hammering the pistons). When it hears it, the ECU retards the ignition to protect the engine. High input means the ECU is reading a voltage above what is possible, usually from an electrical fault, although loud mechanical noise can also play a part. It is sensor 1, on bank 1 or the only one.
Can you drive with P0328?
You can drive, as the ECU usually retards the ignition as a precaution, but the engine is less protected if real knock occurs. Avoid working it hard and get it checked soon.
How do you clear P0328?
With an OBD2 scanner and an app like Final OBD, which clears it for free if it’s stored by the engine control unit. But clearing it only turns the light off: if the cause isn’t fixed, P0328 comes back.
Read it on your car
Final OBD reads and clears engine faults through standard OBD for free, each one explained in plain English. With PRO it also reads the faults of every control unit, each make’s own codes included, and clears them in all of them.
